![doublecad xt v5 reset veiw doublecad xt v5 reset veiw](https://i.pinimg.com/736x/1e/0e/6b/1e0e6bf83bb94ebfb881f298319baded.jpg)
Lock/Ready indicator Number of pig passages Pig number in historyīattery life or external power indicator Time since last reset Time since pig detectedģ16 Stainless steel base attached to pipelineīacklight (for long distance and night viewing) The high-contrast LCD screen gives the operator a clear view of the time of pig passage.Stylus for screen interaction
![doublecad xt v5 reset veiw doublecad xt v5 reset veiw](https://windows-cdn.softpedia.com/screenshots/DoubleCAD-XT_13.png)
in the United States and foreign countries. Dimensions not for construction unless certified. Patent pending in the United States and in foreign countries.ĭata subject to change without notice. If multiple pig passages have occurred, the times of the last 2 to 99 passages may be retrieved by simply scrolling back through the PIG-SIG NIXT memory. In addition, the time of the most recent passage is clearly displayed on an LCD graphic display screen. Also, a bright LCD backlight remains lit for a short period of time following a pig passage. When a pig detection is recorded by the PIG-SIG NIXT, two flashing LED lights visible up to 50 feet away (in bright sunlight) indicate that a recent pig passage has occurred. A maximum operating current of 2 amps at 30 The PIG-SIG NIXT electrical circuitry utilizes a double-pole, double-throw isolated contact closure momentarily triggered and automatically reset after a pig passage. Also, any unit may be wired for communication with a control room or operators SCADA system. All standard units include two LED lights for long-distance viewing and a graphic display with pig passage times. A heater option is necessary for the LCD display to operate at temperatures below -22 F (-30 C). The unit must be hard-wired at temperatures below -4 F (-20 C) or above 130 F (54 C). Operating temperatures (at the pipelines exterior surface) can range from -40 F to 176 F (-40 C to 80 C). All standard units can operate on two standard 1.5-volt D-cell alkaline batteries or can be hardwired to 24 VDC external power. The PIG-SIG NIXT fits 4- through 72-inch (102 mm -1800 mm) line sizes and works on steel pipe wall thicknesses up to 1.5 inches (38.1 mm). Pig speeds can range from 0.03 ft/s (0.01 m/s) to 65 ft/s (20 m/s).
#Doublecad xt v5 reset veiw install
Since the device is fully non-intrusive, no tapping or welding is required, thus saving the operator time and money spent on the installation of conventional signal devices (see five easy steps to install on page 4 of this bulletin).įeaturesThe non-intrusive pig passage indicator provides bi-directional detection of pigs equipped with TDW trip magnets or carbon steel cleaning brushes. The unit is easily attached onto a pipeline, where it can begin scanning for permanent magnet-equipped pigs or certain scrapers with carbon steel cleaning brushes. 60950-1, EN 60950-1 & EN 60529 Certified for Hazardous Locations: CLASS I, DIVISION 1, Groups C, D CLASS II & III, DIVISION 1, Groups E, F, G Enclosure Protection: NEMA 4X, IP 66 ATEX Approved CE 0891 TRAC10ATEX21257X II 2 G Ex d IIC T5 II 2 D Ex tD A21 IP66 T100CĭescriptionThe PIG-SIG NIXT produces accurate and consistent non-intrusive detection of pig passages anywhere within a pipeline system. Flexible extensions up to several hundred feet in length may also be provided for direct burial applications.MET Listing Number (NRTL Listing for USA and Canada): E113028 Complies with: UL 1203, UL 60950-1, UL 50, UL 50E, CSA 22.2 No.
![doublecad xt v5 reset veiw doublecad xt v5 reset veiw](https://4.bp.blogspot.com/-oyYAkZ2ea10/WvOXSTd5LlI/AAAAAAAAA3U/C4BBJ10HpaEbrcn8cKBhBPDsj5oGS264gCLcBGAs/s640/dtm-civil-section-view.png)
Like the mounting base, rigid extensions will be constructed from 316 stainless steel for maximum corrosion protection. For buried pipelines, rigid extensions of up to 15 feet in length can be provided (see table on page 2 for standard extension lengths available). Each unit will be provided with an appropriate length of epoxy-coated galvanized steel chain corresponding to the size of the pipe (see table on page 2 for lengths needed). The mounting base and custom turnbuckle for attachment to the pipe are constructed from 316 stainless steel. The PIG-SIG NIXT is fully certified for hazardous locations requiring explosion-proof devices. Only 3.5 x 3.5 inches of space is required on the pipeline surface for mounting of the device. A lock switch prevents false pig detections when the unit is powered on and transported to another location on a pipeline.
#Doublecad xt v5 reset veiw portable
The standard PIG-SIG NIXT, which may operate on batteries or 24 VDC power and communicate with a SCADA interface, is easily portable at a weight of only 10 pounds. PIG-SIG NIXTNon-intrusive pig passage indicator A detachable terminal block inside the box allows for quick and easy wiring to external power and remote wired communication. The pig signaler is equipped with a field wiring box with a NPT female conduit port. VDC may be applied to the contact closure.